Fisher & Paykel FlexiFit™ 407 Nasal CPAP Mask
$84.00
This is the mask frame system for the Fisher & Paykel FlexiFit™ 407 which includes the mask frame and cushion.
Fisher & Paykel FlexiFit™ 407 Nasal CPAP Mask Overview
The FlexiFit™ 407 Premium Nasal CPAP Mask offers an over-the-nose mask solution that fits better and is super comfortable to wear nightly.
This is the frame system for the Fisher & Paykel FlexiFit™ 407 Nasal Mask and it includes the mask frame and cushion.
Please note: headgear does not automatically come with the order. If you'd like your purchase to include headgear, please select your headgear option above.
-
FlexiFit™ Technology: automatically adjusts to a wide range of nasal and facial contours with one-step fitting and easy adjustments
-
Premium Silicone Seal: seal technology has a soft surface, texture optimizes mask seal
-
Bias Diffuser: advanced air diffuser system prevents air from blowing out of the mask, decreasing noise levels
-
1 — FlexiFit™ 407 Mask Frame
-
1 — Cushion and Seal
-
1 — Glider™ Strap
-
1 — Elbow & Valve
Please note: headgear does not automatically come with the order. If you'd like your purchase to include headgear, please select your headgear option above. If you select a headgear option, the following will be included:
-
1 — FlexiFit™ 407 Headgear
-
2 — Headgear Clips
-
1 — Easy-Release Cord
Breathing Style:
-
Nasal Breathers
- Mouth Breathers (when paired with a CPAP mask chinstrap)
Sleeping Style:
-
Back Sleepers
-
Side Sleepers
-
Active Sleepers
Additional Considerations:
-
High Pressure Settings
- Glasses Wearers
- Claustrophobia
- Facial Hair
-
Full Field of View for Reading or Watching TV Before Bed
-
Tossing and Turning During Sleep
Fitting Your Mask:
Remove the plastic cover from the Silicone Seal.
- Remove plastic cover from Silicone Seal.
- Holding your mask in one hand, spread the Stretchgear Headgear with your free hand, just enough to fit comfortably over your head.
- Lightly hold the mask against your face covering the nose, then slowly pull the Headgear over your head.
- Attach the Headgear to the Glider Strap.
- Pull the lower straps as low as possible down back of your neck. Gently tighten straps to remove slack. Connect to CPAP/Bi-Level machine set at prescribed pressure.
- If necessary, tighten the lower straps to eliminate any leaks (avoid overtightening the straps).
- When you need to remove your mask, unhook the Stretchgear™ Headgear from the Glider Strap.
Fitting Tips
- Forehead pads should rest gently on the forehead without top straps being pulled too tight.
- If there are any leaks after gently tightening the top and lower straps, pull the mask slightly out from the face while straps are still attached. This will allow Silicone Seal to inflate with air. Put the mask back onto the face.
Assembling Your Mask:
Refer to the assembly diagrams in these instructions.
- Place Silicone Seal face down onto flat surface. With thick side of Foam Cushion facing down, place into Silicone Seal.
- Starting with the slot at the apex of the Silicone Seal, assemble onto Mask Base. Push firmly together.
- Lay the Stretchgear Headgear flat with the loop side down. Position the assembled mask over the Headgear and attach the four straps into the corresponding slots in the Forehead Rest and the Glider Strap. This can
be done without undoing the VELCRO® brand tabs, by sliding the Headgear into
the slots.
| Operating Therapy Pressure Range |
| 3 to 25 cmH²O |
CPAPsupplies.com: CPAP Supplies Replacement Schedule
FlexiFit™: Introduction
FlexiFit™: Fitting Guide
- CPAP Mask Frame Replacement Frequency: Resupply Every 3 Months
- CPAP Mask Cushions/Pillows Replacement Frequency: Resupply Every 2 Weeks
- CPAP Mask Headgear Replacement Frequency: Resupply Every 6 Months
CPAPsupplies.com: CPAP Supplies Replacement Schedule
Cleaning Guide
Regularly cleaning your CPAP mask parts and components is crucial for avoiding the accumulation of bacteria, debris, oils, and other contaminants. This will help prevent the buildup of germs that may cause skin irritation and other unwanted side effects.
Before following the instructions below, first make sure your CPAP machine is unplugged from the power source, disconnect your mask and air tubing from your CPAP machine, and disassemble your mask components into 3 parts (nasal cushions, headgear, and frame):
| Part | Cleaning Frequency | Instructions |
|
Nasal Cushions |
Daily |
|
|
Mask Frame |
Weekly |
|
|
Headgear |
Weekly |
|
|
Chinstrap |
Weekly |
|
*Avoid using strong detergents or soaps, especially those that contain harsh chemicals, perfumes, dyes, moisturizers, or alcohol.
You can find more useful information regarding CPAP cleaning with this blog:
| Brand | Fisher & Paykel |
|---|---|
| SKU | pb_HC407 |
| Model | pb_HC407 |
| UPC | 09420012428219 |
| Prescription Required | No |
| Manufacturer's Warranty | 30-day limited manufacturer's warranty |
| FSA/HSA Eligible | Yes |
| Included | 400HC502, 400HC301 |
