Fisher & Paykel Forma™ Full Face CPAP Mask with Headgear
The Fisher & Paykel Forma™ Full Face Mask forms a superior seal and provides even more comfort with a greater range of movement through the active contouring of the FlexiFoam™ Cushion.
Fisher & Paykel Forma™ Full Face CPAP Mask with Headgear Overview
The Forma™ Full Face Mask provides even more comfort with updated features like the FlexiFoam™ cushion for support and the under-the-chin design that enhances sleep performance. The full face cushion fits under the chin and comes with a highly contoured silicone seal for maximum comfort and stability.
The T-Piece forehead support provides added stability and auto adjusts for hassle-free fitting.
The inner foam cushion helps contour the mask to the face and promotes optimal frame alignment.
-
FlexiFit™ Technology automatically adjusts to a wide range of facial contours to ensure easy fitting
-
FlexiFoam™ Cushion provides greater comfort with active contouring that conforms naturally to the face
-
Glider Strap allows for freedom of movement while keeping seal intact to prevent leaks
-
Under-Chin Design provides stability by keeping the seal tight when the jaw moves during sleep
-
T-Piece Mask Base adds stability and complements the under-chin design for hassle-free fitting
-
Premium Silicone Seal has a soft surface, frosted texture optimizes mask seal
-
Efficient Bias Diffuser offers an advanced air diffuser system that prevents air from blowing out of the mask, decreasing noise levels
-
1 — Forma™ Mask Frame
-
1 — Cushion and Seal (of selected size)
-
1 — Glider™ Strap
-
1 — Elbow & Valve
-
1 — Forma™ Headgear
-
2 — Headgear Clips
-
1 — Easy-Release Cord
If you're looking to purchase the Fisher & Paykel Forma™ Full Face CPAP Mask components without a prescription, you can find them here.
-
Small - 400470
-
Medium & Large - 400471
-
Extra Large - 400473
Breathing Style:
-
Mouth Breathers
Sleeping Style:
-
Back Sleepers
-
Side Sleepers
Additional Considerations:
-
High Pressure Settings
-
Chronic Allergies or Nasal Congestion
Assembling Your Mask:
Refer to the assembly diagrams in these instructions.
- Place Silicone Seal (C) face down on a flat surface. With the thick side of the Foam Cushion (D) facing down, place onto Silicone Seal.
- Place Silicone Seal (C) and Foam Cushion (D) into the Mask Base (A).
- Push the Non-Rebreathing Valve (J) onto the Elbow (B), and attach to Mask Base.
- Lay the Headgear (K) flat with the label side down. Position the assembled mask over the Headgear and attach the four straps into the corresponding slots in the Mask Base and the Glider™ Strap (E). This can be done without undoing the Velcro® Tabs by sliding the Headgear into the slots.
Fitting Your Mask:
Remove all packaging before using the mask.
Refer to the fitting diagram and assembly diagram above.
- Remove plastic cover from Silicone Seal.
- Unclip the Headgear (K) from the Glider™ Strap (E) by pulling the Easy-Release Cord (I) towards your nose. Holding your Mask Base (A) in one hand, spread the Headgear with your free hand, just enough to fit comfortably over your head.
- Lightly hold the mask against your face, with the bottom of the Silicone Seal under your chin, and spread the Headgear over your head with your free hand.
- Reattach the Headgear Clip (H) to the Glider™ Strap.
- Gently adjust the top horizontal straps, then the lower horizontal straps, then the top crown straps. Ensure the top of the Silicone Seal remains stable on the bridge of the nose, and the bottom remains fixed under the chin. Ensure that the Glider™ Strap is centered.
- Connect the CPAP/Bi-Level machine hose running at the prescribed pressure to the mask.
Fitting Tips:
- If necessary, pull the mask slightly away from your face while the straps are still attached.
This allows the Silicone Seal to inflate. Put the mask back on your face. - If leaks occur around the upper half of the mask, gently tighten the top horizontal straps.
- If leaks occur around the lower half of the mask, gently tighten the lower horizontal straps. (Avoid over-tightening the straps.)
- When you need to remove your mask unclip the Headgear from the Glider™ Strap by pulling the Easy-Release Cord towards your nose.
| Operating Therapy Pressure Range |
| 3 to 25 cm H²O |
CPAPsupplies.com: CPAP Supplies Replacement Schedule
- CPAP Mask Frame Replacement Frequency: Resupply Every 3 Months
- CPAP Mask Cushions/Pillows Replacement Frequency: Resupply Every 2 Weeks
- CPAP Mask Headgear Replacement Frequency: Resupply Every 6 Months
CPAPsupplies.com: CPAP Supplies Replacement Schedule
Cleaning Guide
Regularly cleaning your CPAP mask parts and components is crucial for avoiding the accumulation of bacteria, debris, oils, and other contaminants. This will help prevent the buildup of germs that may cause skin irritation and other unwanted side effects.
Before following the instructions below, first make sure your CPAP machine is unplugged from the power source, disconnect your mask and air tubing from your CPAP machine, and disassemble your mask components into 3 parts (mask cushions, headgear, and frame):
| Part | Cleaning Frequency | Instructions |
|
Mask Cushions |
Daily |
|
|
Mask Frame |
Weekly |
|
|
Headgear |
Weekly |
|
|
Chinstrap |
Weekly |
|
*Avoid using strong detergents or soaps, especially those that contain harsh chemicals, perfumes, dyes, moisturizers, or alcohol.
You can find more useful information regarding CPAP cleaning with this blog:
| Brand | Fisher & Paykel |
|---|---|
| SKU | p_forma_full_face |
| Model | p_forma_full_face |
| UPC | 09420012421777, 09420012421814,09420012421890 |
| Prescription Required | Yes |
| Weight | 0.37 lbs |
| Manufacturer's Warranty | 90-day limited manufacturer's warranty |
| FSA/HSA Eligible | Yes |
| Included | 400471, 400473, 400470 |
1 Item Added to Cart
