Fisher & Paykel FlexiFit™ 405 Nasal CPAP Mask System without Headgear
The Fisher & Paykel FlexiFit™ 405 Nasal CPAP Mask Kit without Headgear features F&P's FlexiFit™ technology that automatically adjusts in order to accomodate a wider range of face shapes. This mask kit incudes two cushions and foam inserts (1 - Small, 1 - Large).
Please note: headgear is not included with this order, but can be purchased separately here.
Fisher & Paykel FlexiFit™ 405 Nasal CPAP Mask System without Headgear Overview
The FlexiFit™ 405 Mask without Headgear by Fisher & Paykel is a nasal CPAP mask that offers great comfort and flexibility.
Featuring F&P's FlexiFit™ technology that automatically adjusts to accommodate a wider range of facial contours and shapes.
Please note: headgear is not included with this order, but can be purchased separately here.
-
Lightweight, compact design
-
FlexiFit™ technology provides a fit for a wider range of face shapes
-
Glider straps provide stability without restricting movement
-
Cushions and foam inserts provide enhanced comfort
-
1 — FlexiFit™ 405 Mask Frame
-
1 — Small - FlexiFit™ 405 Foam Cushion & Silicone Seal - 400HC427
-
1 — Large - FlexiFit™ 405 Foam Cushion & Silicone Seal - 900HC428
-
1 — Elbow & Diffuser - 900HC441
-
1 — Swivel Connector - 900HC438
-
1 — Diffuser Cap - 900HC440
-
1 — Glider Strap - 400HC418
Please note: headgear is not included with this order, but can be purchased separately here.
Breathing Style:
-
Nasal Breathers
- Mouth Breathers (when paired with a CPAP mask chinstrap)
Sleeping Style:
-
Back Sleepers
-
Side Sleepers
-
Active Sleepers
Additional Considerations:
-
High Pressure Settings
- Glasses Wearers
- Claustrophobia
- Facial Hair
-
Full Field of View for Reading or Watching TV Before Bed
-
Tossing and Turning During Sleep
Fitting Your Mask:
Remove the plastic cover from the Silicone Seal.
- Holding your mask in one hand, spread the Headgear with your free hand just enough to fit comfortably over your head.
- Lightly hold the mask against your face covering the nose then slowly pull the Headgear over your head.
- Attach the Headgear to the Glider Strap.
- Pull the lower straps as low as possible down back of neck. Gently tighten straps to remove slack. Connect to CPAP/Bi-Level machine at prescribed pressure.
-
- If necessary, tighten the lower straps to eliminate any leaks (Avoid overtightening the straps).
- Use the Silicone Seal that provides the best fit for you. Small and Large are both provided with your mask.
- When you need to remove your mask, unhook the Headgear from the Glider Strap.
Fitting Tips:
- Forehead pads should rest gently on the forehead without top straps being pulled too tight.
- If there are any leaks after gently tightening the top and lower straps, pull the
mask slightly out from the face while straps are still attached. This will allow the
Silicone Seal to inflate with air. Put the mask back onto the face.
Assembling / Disassembling Your Mask:
Refer to the assembly/disassembly diagrams in these instructions.
- Place the Foam Cushion into the Mask Base.
- Starting at the apex of the mask, fit the Silicone Seal over the Foam Cushion and onto the Mask Base, finishing at the bottom of the mask.
- Push the Elbow into the Mask Base.
- Lay the Headgear flat with the loop side down. Position the assembled mask over the Headgear and attach the four straps into the corresponding slots in the Forehead Rest and the Glider Strap. This can be done without undoing the Velcro tabs, by sliding the Headgear into the slots.
| Operating Therapy Pressure Range |
| 3 to 25 cmH²O |
CPAPsupplies.com: CPAP Supplies Replacement Schedule
FlexiFit™ 405: Introduction
FlexiFit™ 405: Fitting Guide
- CPAP Mask Frame Replacement Frequency: Resupply Every 3 Months
- CPAP Mask Cushions/Pillows Replacement Frequency: Resupply Every 2 Weeks
CPAPsupplies.com: CPAP Supplies Replacement Schedule
Cleaning Guide
Regularly cleaning your CPAP mask parts and components is crucial for avoiding the accumulation of bacteria, debris, oils, and other contaminants. This will help prevent the buildup of germs that may cause skin irritation and other unwanted side effects.
Before following the instructions below, first make sure your CPAP machine is unplugged from the power source, disconnect your mask and air tubing from your CPAP machine, and disassemble your mask components into 3 parts (nasal cushions, headgear, and frame):
| Part | Cleaning Frequency | Instructions |
|
Nasal Cushions |
Daily |
|
|
Mask Frame |
Weekly |
|
*Avoid using strong detergents or soaps, especially those that contain harsh chemicals, perfumes, dyes, moisturizers, or alcohol.
You can find more useful information regarding CPAP cleaning with this blog:
| Brand | Fisher & Paykel |
|---|---|
| SKU | 6616 |
| Model | 900HC406 |
| HCPCS | A7034 |
| UPC | 9420012428486 |
| Prescription Required | No |
| Weight | 0.50 lbs |
| Manufacturer's Warranty | 90-day limited manufacturer's warranty |
| Color | Clear & Gray |
| FSA/HSA Eligible | Yes |
| Size | One Size |
1 Item Added to Cart
